Send the same harness drawing to five manufacturers, and the prices you get back can vary widely. The gap is rarely random. Every figure on a wiring harness quote traces back to a small set of cost drivers, and most are fixed by decisions made on the drawing long before a supplier sees it.
We’ll break down where the money in a harness goes, which of those costs a buyer can influence, and how to compare a UK quote with an overseas one on equal terms. It draws on SIC’s experience building wiring harnesses, cable assemblies and box builds since 1964, from operations in both the UK and China, and on design and sourcing work that has saved SIC’s clients over £1.3 million in production costs.
Why two quotes for the same harness can look so different
A harness unit price is the sum of six things: materials, assembly labour, set-up and tooling, testing, the volume and schedule it is built to, and the cost of getting it to your line. Suppliers weight these differently. One may absorb tooling into the unit price; another lists it separately. One may quote a metal price valid for 30 days; another builds in a buffer. One may include 100% electrical testing; another samples.
Before comparing totals, it is worth asking each supplier to break the quote into those six lines. The comparison usually becomes much clearer, and the conversation moves from “why is yours higher?” to “which of these do we actually need?”
Materials: the largest line, and the one design controls most
On most harnesses, materials make up the largest single share of the price. That share is set almost entirely by the specification.
Conductor. Copper prices have reached record levels during 2025 and 2026, and wire is priced on the metal it contains. Any oversized conductor across a long harness adds cost to every unit. It is worth checking whether every circuit genuinely needs the gauge specified, or whether one size has been applied across the board for convenience. It is also worth checking how long a quote’s metal price is held, as a short validity window can make a lower headline price less firm than it looks.
Insulation. PVC, cross-linked polyethylene, silicone and PTFE-insulated wires sit at very different price points. A common pattern is a high-temperature insulation specified for the whole harness when only one branch runs near a heat source. Specifying by zone rather than by harness can reduce material cost without changing performance where it matters.
Connectors and terminals. These are often the most expensive components per circuit, and the part number on the drawing decides how much room a supplier has to manage cost. A single-source branded connector fixes both price and lead time. Where the drawing allows approved equivalents, a manufacturer with a broad sourcing network can offer alternatives that meet the same specification at a lower price or with better availability. SIC’s materials supply and logistics team handles this procurement as part of the build, so the buyer doesn’t have to manage dozens of component suppliers.
Protection. Braided sleeving, convoluted conduit, heatshrink, tape and overmoulding each add material and labour. They exist to protect against abrasion, moisture, heat and vibration, so the question is not whether to use them, but whether the level of protection matches the environment the harness will see.
Labour: where the hours go
Cutting, stripping and crimping are largely automated on modern equipment. Much of what follows is still done by hand. Wires are routed on an assembly board, terminals are inserted into housings, branches are taped or sleeved, splices are made and labels applied. That manual time is where labour cost builds up.
The number of circuits is only part of the picture. Labour rises with:
- the number of branches and breakouts
- splices, which take longer than a straight termination
- mixed termination types within one harness
- tight tolerances on breakout positions and lengths
- twisted pairs, shielding and drain wire terminations
- labelling and identification requirements
This is also the line where overseas labour rates make the biggest visible difference to a unit price. The more labour-intensive a design, the wider that gap appears on paper. That is a reason to look carefully at what the labour is being spent on before assuming the only way to reduce it is to move production.
Set-up, tooling and one-off costs
Every new harness carries some non-recurring engineering cost. Crimp applicators may be needed for specific terminals. An assembly board must be built to the harness layout. Test fixtures are made to match the connectors. Overmoulded harnesses need a mould tool.
These costs are paid once and spread across the units built. On a long-running, high-volume part, they become negligible per unit. On a short run, they can dominate the price. A good quote shows them separately, so you can see what you are paying for and what you will not pay for again on repeat orders. SIC’s prototype and pre-production stage is where most of this is settled, and where design changes are cheapest to make.
Testing and quality
Electrical testing confirms continuity and correct pin-out on every circuit. Depending on the application, it may extend to insulation resistance, high-voltage testing and crimp pull testing. Testing adds time and fixture cost, which is why some low-price quotes include sampling rather than 100% testing.
The cost of testing is small compared with the cost of a harness failing after it has been fitted into a finished product. When comparing quotes, confirm exactly what testing is included and which quality standards the supplier is accredited to. SIC holds ISO 9001:2015, ISO 14001:2015 and UL accreditation, and its product testing page sets out how assemblies are verified before dispatch.
Volume, batch size and scheduling
Larger batches spread set-up time and allow materials to be bought in economic quantities, so unit prices fall as volumes rise. The trade-off is cash and space. Ordering a year’s supply to reach a price break ties up working capital and warehouse room, and leaves stock exposed if the design changes.
An agreed annual forecast with scheduled deliveries often delivers better overall results than a single large order. The manufacturer can plan material purchasing against the forecast while you take delivery as you need it. Sharing realistic volumes at the quoting stage, rather than a single batch quantity, gives a supplier more scope to price accordingly.
Comparing a UK price with an overseas price
An overseas quote is usually an ex-works or free-on-board unit price. A UK quote is usually closer to a delivered price. Comparing the two directly understates the true cost of the overseas option. The figure that matters is landed cost: the total cost of having a usable harness on your production line.
None of this means overseas supply is the wrong choice. For stable, high-volume, labour-intensive designs, it can be the most economical route. For lower volumes, frequent design changes, or harnesses critical to keeping a line running, UK manufacture often costs less once you factor in the above. Because SIC operates in both the UK and China, it can quote both routes for the same harness and show where the break-even point sits. For the wider supply chain case, our article on why more UK manufacturers are bringing wiring harness production closer to home covers the risk and continuity side in more detail.
Design decisions that reduce cost before the first quote
The biggest savings are made at the drawing stage, because that is where most of the cost is fixed. The changes that tend to make the most difference are:
- Standardise connectors and terminals across harness variants and product lines, so the same parts and tooling are reused.
- Rationalise wire gauges and colours. Fewer distinct wire types means less set-up and simpler stock.
- Allow approved equivalents on the drawing wherever the application permits, so the supplier can manage component price and availability.
- Relax tolerances that are not functional. A breakout length held to a few millimetres costs more to build and inspect than one with a sensible working tolerance.
- Consolidate variants. Several near-identical harnesses can sometimes become one, with optional branches left unterminated.
- Check whether a harness is the right product. Some requirements are better met by a simpler cable assembly, which can be quicker and cheaper to build.
- Involve the manufacturer early. A design review before the drawing is released costs nothing and often finds savings that are expensive to make after tooling is built.
If the harness is going into a larger unit, it is also worth asking whether buying the complete box build costs less than buying the parts and assembling them in-house.
Getting a quote that you can rely on
An accurate quote depends on an accurate brief. The more complete the drawing, bill of materials, volumes and test requirements, the less a supplier has to allow for unknowns, and the less likely the price is to change once production starts. Our cable harness specification checklist sets out what to include.
SIC is a UK wiring harness manufacturer serving over 100 customers across 24 sectors, including automotive, medical, switchgear and vending. If you would like a harness reviewed for cost, or a UK and overseas price compared on a landed-cost basis, contact the SIC team with your drawing and expected volumes.